It seems so simple to just slide some string between your teeth to clean those hard-to-reach areas. While the idea is simple, there are a few techniques that you need to master in order to maximize the return on the time you spend flossing.
Here are ten common mistakes that people make when they floss:
1 – Not Flossing the Sides of Both Teeth
If you just slide the floss down, and then pull it up, you are only getting 50% of the job done. When you move the floss up between two teeth, you need to make sure that you are cleaning the side of both teeth. One of the favorite places for plaque to hide is between teeth. If you’re only removing plaque from the side of one of the teeth, you could easily get a cavity on the tooth that you’re not flossing.
2 – Using the Same Section of Floss Between All of Your Teeth
When you floss you are removing bacteria from between your teeth and below the gum-line. If you use the same section of floss for all of the teeth in your mouth, you are spreading around a lot of bacteria. Of course you still are loosening the plaque, which has its benefits, but if you use a new section of floss each time you floss between two teeth, you will be loosening the plaque without putting plaque that you’ve already removed back in between your teeth.
3 – Snapping the Floss Down Hard Between Your Teeth
To get the floss to go between a tight contact between two adjacent teeth, try working the floss back and forth applying a firm but controlled downward pressure.
Snapping the floss down between the teeth can not only injure your gums in the short-term, but the trauma can cause your gums to recede. Do it enough, and you’ll cause gum disease.
4 – Not Flossing Behind the Very Back Teeth
Even though there isn’t a tooth next to it, it is still important to clean behind the four teeth that are all the way in the back of your mouth (two teeth on each side in the upper and lower jaws.) This can help remove bacteria that has made its way between your tooth and gums.
5 – Flossing Aimlessly Without a Plan
When you floss, you need to have a road-map of what order you are going to floss your teeth in, or you can quickly become confused and miss some teeth or even a quadrant of your mouth. It may be easiest to start in the upper right and go to the upper left, then come down to the lower teeth in the bottom left and move across to the bottom right.
However, as long as you have a plan, it really doesn’t matter which teeth you floss first. Personally, I start right in the middle of my upper teeth and work my way back on one side and then on the other. Then I do the same thing on the lower teeth. Just find a “floss order” that works for you and stick to it so that you don’t forget to floss any teeth.
6 – Not Flossing Around Dental Appliances
Many people don’t know that if they have fixed dental appliances in their mouth, they need to floss around them. For example, if you have a bridge, it is necessary to use a floss threader, or get something similar to Oral-B Superfloss.
I had braces on my lower teeth when I was a teenager. After I had them removed, the orthodontist cemented a wire that connects to each of my six lower front teeth. This stabilizes them, but also makes it impossible to use conventional floss due to the wire. Because of this, I have to use Superfloss or floss threaders to get under the wire so I can floss and maintain my gum health.
7 – Quitting When Your Gums Bleed
Blood may scare some people when they floss because they think that they are hurting their gums if they bleed. You are not hurting them as long as you’re not flossing too hard (see mistake #3.)
Most likely, the reason they bleed is because they haven’t been flossed in a while and the gum tissue has become red and inflamed. This is a condition known as gingivitis and it occurs because the body is sending more blood to the gum. This is to help the tissue fight all of the plaque that is accumulating. When you floss, you are removing that plaque, and since the tissue is inflamed and engorged with blood, you are causing some of the blood to leak out. After a few days, your gums should return to health and you can floss normally without any bleeding.
8 – Not Spending Enough Time With Your Floss
Most people have 28 teeth if they’ve had their wisdom teeth extracted. When you floss, you need to get both sides of the teeth (even the most posterior teeth – see mistake #4.) That means that there are 56 sides that you need to get. You should be spending a couple of seconds with each side, scraping up and down against the tooth a few times before moving onto the next surface. That means that it will probably take you around two minutes to floss your entire mouth if you have a full set of teeth.
9 – Not Applying Pressure to the Tooth Surface
When you floss, you want to be careful to avoid using too much downward pressure so you don’t damage your gums. However, when you are flossing against the side of a tooth, you want to make sure that you are pushing the floss against the tooth surface enough to be able to remove the plaque.
10 – Only Using Floss to Remove Food
Unfortunately, lots of people think that the only reason for flossing is to remove food that has gotten wedged between their teeth. I think many people end up doing this because they can see the food between their teeth — they can’t see the plaque. An easy solution to this problem is to use a plaque disclosing tablet/solution to visualize the plaque on your teeth.
When you floss, your primary goal should be to scrape against each tooth to remove as much plaque as you can. As long as you are doing this, you should be getting rid of the food between your teeth without even thinking about it.
Floss Correctly and Keep Your Teeth For Your Whole Life
By avoiding these ten common mistakes, you will be able floss more efficiently which will lead to greater oral health. Since many cavities start out between two teeth, you will be able to prevent many cavities by regularly flossing and avoiding these ten flossing mistakes.
For more information on flossing, please visit OralAnswers.com.